12.7 mm Flat Top Modular Belt for Food Conveying
XCY12701A- Pitch
- 12.7 mm
- Thickness
- 8.8 mm
- Pin Ø
- 5 mm
- Width Min.
- 76 mm
- Backflex Radius
- 20 mm
XCY12700A · Modular belts
12.7 mm Flat Top Modular Conveyor Belt
A small-pitch belt with a closed top for straight product conveying. Modular widths allow the supporting surface to be sized for the line.
Product Inquiry
10hours
Usual reply time
Similar & related products
CHECK THE DETAILS
Specifications
Compare belt dimensions and material performance to check your conveyor fit, load and operating conditions.
| Units | Pitch | Thickness | Pin Ø | Width Min. | Backflex Radius | Width Increment | Open Area |
|---|---|---|---|---|---|---|---|
| mm | 12.7 | 10 | 5 | 10 | 50 | 0 % | |
| in | 0.5 | 0.394 | 0.197 | 0.394 | 1.969 |
| Dimension | mm | in |
|---|---|---|
| Pitch | 12.7 | 0.5 |
| Thickness | 10 | 0.394 |
| Pin Ø | 5 | 0.197 |
| Width Min. | ||
| Backflex Radius | 10 | 0.394 |
| Width Increment | 50 | 1.969 |
| Open Area | 0 % | |
| Belt Material | Rod Material | Working Load | Belt Weight | Temperature Range |
|---|---|---|---|---|
| POM | PP | 16000 N/m at 21 °C | 8.7 kg/m² | 0–85 °C |
| POM | PA | 18000 N/m at 21 °C | 8.8 kg/m² | -5–85 °C |
| PP | PP | 11000 N/m at 21 °C | 5.8 kg/m² | 0–105 °C |
| PE | PE | 7000 N/m at 21 °C | 8.8 kg/m² | -45–65 °C |
Standard nominal belt width: W = 50 × N mm. W is width in millimetres; N is the whole-number count of 50 mm width units. Modules: 50 / 100 mm at the edges and 150 mm in the centre. Actual width can be 0.1–0.3% below nominal due to material shrinkage.
CHECK BEFORE ORDERING
Check dimensions. Match the parts.
Share belt or chain photos (both sides), sprocket and interface photos, key dimensions, conveyed product details, operating conditions and special requirements.
Check FitDimensions & installation
Provide belt or chain width, loop length and available installation and return clearance.
Allow for running clearance; nominal width alone is not an installation check.Sprockets & matching parts
Share sprocket photos, tooth count, shaft bore dimensions and equipment interfaces.
Matching pitch alone does not establish sprocket compatibility.Product & operating conditions
Provide product size and weight, line speed, transfer gaps, temperature and cleaning conditions.
Confirm the configuration for the actual process before ordering.PRODUCT QUESTIONS
FAQ
More answers about product selection, installation and maintenance.
Does a closed top prevent all liquid from passing through?
No. A closed carrying surface is not a sealed conveyor. Liquid can still pass at joints or edges, depending on the installation.
Can I choose the transfer gap from belt pitch?
No. The end geometry, support, speed and product base determine the usable transfer arrangement. Check them as an assembly rather than selecting a gap from pitch alone.
Why can measured width differ from nominal width?
The material can shrink after moulding. The listed width allowance is 0.1–0.3% below nominal, so installation clearance must use the actual supplied width.
PLAN YOUR INSTALLATION
Product Documents
Get belt specifications, sprocket data and installation drawings to check dimensions and plan your equipment.
Dimensions & materials
Dimensions, materials, working load and operating conditions.
Sprockets & drive fit
Tooth counts, bore sizes and sprocket dimensions for drive matching.
Drawings & installation
Product geometry, mounting dimensions and installation clearances.
Tell us the model and the documents you need for selection or installation.
Request Documents
