12.7 mm Flat Top Modular Belt for Food Conveying
XCY12701A- Pitch
- 12.7 mm
- Thickness
- 8.8 mm
- Pin Ø
- 5 mm
- Width Min.
- 76 mm
- Backflex Radius
- 20 mm
XCY15200A · Modular belts
Flat Top Modular Belt for Food and Packaging
A closed carrying surface supports products on straight food, beverage and packaging conveyor sections.
Product Inquiry
10hours
Usual reply time
Similar & related products
CHECK THE DETAILS
Specifications
Compare belt dimensions and material performance to check your conveyor fit, load and operating conditions.
| Units | Pitch | Thickness | Pin Ø | Width Min. | Backflex Radius | Width Increment | Open Area |
|---|---|---|---|---|---|---|---|
| mm | 15.24 | 8.7 | 4.5 | 152 | 25 | 152.4 | 0 % |
| in | 0.6 | 0.343 | 0.177 | 5.984 | 0.984 | 6 |
| Dimension | mm | in |
|---|---|---|
| Pitch | 15.24 | 0.6 |
| Thickness | 8.7 | 0.343 |
| Pin Ø | 4.5 | 0.177 |
| Width Min. | 152 | 5.984 |
| Backflex Radius | 25 | 0.984 |
| Width Increment | 152.4 | 6 |
| Open Area | 0 % | |
| Belt Material | Rod Material | Working Load | Belt Weight | Temperature Range |
|---|---|---|---|---|
| POM | PA | 14000 N/m at 21 °C | 6.35 kg/m² | -5–85 °C |
| POM | PP | 12000 N/m at 21 °C | 6.35 kg/m² | 0–85 °C |
| PP | PP | 9000 N/m at 21 °C | 4.40 kg/m² | 0–105 °C |
| PE | PE | 7000 N/m at 21 °C | 4.69 kg/m² | -45–65 °C |
The width increment shown applies to standard assemblies.
CHECK BEFORE ORDERING
Check dimensions. Match the parts.
Share belt or chain photos (both sides), sprocket and interface photos, key dimensions, conveyed product details, operating conditions and special requirements.
Check FitDimensions & installation
Provide belt or chain width, loop length and available installation and return clearance.
Allow for running clearance; nominal width alone is not an installation check.Sprockets & matching parts
Share sprocket photos, tooth count, shaft bore dimensions and equipment interfaces.
Matching pitch alone does not establish sprocket compatibility.Product & operating conditions
Provide product size and weight, line speed, transfer gaps, temperature and cleaning conditions.
Confirm the configuration for the actual process before ordering.PRODUCT QUESTIONS
FAQ
More answers about product selection, installation and maintenance.
Does the small pitch guarantee that a small pack will cross the transfer?
No. The pack base must remain supported across the conveyor end and receiving gap. Check the sprockets, transfer plate, conveyor heights and speed with the smallest pack being handled.
Can a damaged area be repaired without replacing the complete belt?
The modular construction allows an affected section to be replaced. Check the adjacent modules, rods and drive components for wear as well, and carry out the work with the conveyor stopped and isolated.
What should I specify if the belt passes through a warm wash stage?
Provide the wash temperature, chemicals, exposure time and conveying load. Choose a listed belt and rod combination for those conditions; an operating-temperature range alone does not establish chemical suitability or the permitted load.
PLAN YOUR INSTALLATION
Product Documents
Get belt specifications, sprocket data and installation drawings to check dimensions and plan your equipment.
Dimensions & materials
Dimensions, materials, working load and operating conditions.
Sprockets & drive fit
Tooth counts, bore sizes and sprocket dimensions for drive matching.
Drawings & installation
Product geometry, mounting dimensions and installation clearances.
Tell us the model and the documents you need for selection or installation.
Request Documents
